eHam.net Classifieds Search Results

TL922 power switch wanted

Power switch needed for TL922 anyone?

WTB Kenwood TL-922 Band Switch

Hello I am in need of a Band switch for the TL922 amplifier I need the A band switch that is the ceramic one. Will pay top dollar for excellent condition switch!

WTB PART FOR YAESU FL-7000 Amp

Looking for the small 5" vertical piece on the left side of the face, in good condx. 73 Dwight NS9I

Eimac CX150 & CX250 tubes

Eimac CX150 & CX250 tubes. Some NOS, some used but tested. I have a few of each. Pls email for pictures & details

Eimac 4-400A tube sockets

I have two Eimac metal tube sockets for the 4-400A tubes and others. These are used but in excellent condition. Price is $165.00 each, or both for $310.00. Shipped free to U. S. and very reasonable to out of country.

Complete 6m Vacuum Variable Tank Circuit

Offering, as a result of an aborted Ameritron AL1500 dedicated 6m retrofit project,a complete high voltage 2KW+ tank circuit component package for the homebrewer. Included in the parts offering is a brand new small footprint 5KV 20-100pFd plate tune vacuum variable, pre-tuned solid copper tank coil, wide spaced 180pFd air variable antenna tune capacitor, a completely assembled HV plate choke wound on a threaded porcelain rod,a 10KV bypass cap, and a 5KV 500pFd ceramic RF blocking capacitor. Additional components include a 1/4" shaft(s) bronze bevel gear right angle drive with removable mounting bracket, a porcelain shaft insulator with a shaft extender, and a series of porcelain standoffs. This array of components all contribute flexibility to the builder's design and enclosure space constraints when considering mounting the vacuum variable capacitor either to the front panel or inboard with the angle drive. $185 + shipping

Eimac SK 406

Eimac air chimney $10 plus shipping

500 pf Doorknob Capacitor Needed

I need one or two 500 pf (470 pf is also OK) Doorknob Capacitors with a minimum Working Voltage of 7.5 KVDC. They must have an OD around 0.8" to fit the space. Female 6-32 threads are also required. Something like the 858S Series would do.

SSB ele

6m SSB Mast mount Pre-amp needs repair..Make offer.

wtb sb220 without tubes or similiar

would like old amp with good hv transformer similiar to sb 220 or something using 2 4-400's cosmetics not important. or just a good hv transformer I am disabled so would like something reasonably priced.let me know what you have. thank you andy kd8exl

Gonset GSB-201 Tranny 1600 & 6.3 @ 16 amps

Original Transformer. Made for 4 x 811A Tubes. Secondary:1600 & 6.3 @ 16 amps.(no CT) b 120 vac input only. Also HV Inductor from same amp and other original parts. photo shows both on amp chassis.

50V, 20Amp Switching PS

Lightweight (5lb) power supply runs from 110 or 220. At 110, output is reduced to 14A. $75

FS: Amplifier Parts

1N2804A 6.8V 50 Watt Zener Diodes, TO-3 NOS -- $10 each Stancor Transformer P-6461 117 VAC Primary / 10VCT @ 10 A Secondary, used -- $25 Triad Transformers -- 115V 60CPS Primary F21A 6.3VCT @ 10A Secondary, Used -- $20 F28U 6.3/7.5 VCT @ 25A Secondary, NOS -- $40 Cardwell -- XR-1000PS 1000pF Air Variable Capacitors. About 4.5" x 4" x 3.5" overall including plate travel. .030 air gap. Used, Good condition. $20 ea. Sprague 3600pF @ 30KV Doorknob capacitor. Red epoxy encased style -- $25 28uH Roller Coil, 42 Turns #12, a skosh over 2" in diameter, 8 TPI, 3" x3" x 7" overall plus 3" shaft. Fiberglass coil supports. I think that this is the coil employed in the MFJ-989 antenna tuner. Excellent condition. $50 Toroidal Tank coil -- The core is fiberglass & resin encased. It is currently wound with 20 turns of #12 wire. There are notches in the form for up to 40 turns. It is a bit over 4 inches in diameter and about 1-3/4" thick. This was made by Bob, W6YUY. See his article in August 1985 Ham Radio magazine "Design a Toroidal Tank Circuit for you Vacuum Tube Amplifier". $50 Eimac -- Databook set circa 1985 in two large yellow Eimac 3 ring binders. Includes data sheets from 1976 edition and earlier. Very good condition. $200 Eimac HR-8 plate dissipator used, a mite tarnished $10 Eimac HR-6 plate dissipators, NOS pair $20. Eimac HR-6 plate dissipators used, tarnished, pair $10 Eimac SK-620 sockets, "unused" pair. One is a SK-620; the other a SK-620A. Probably 40 years old, a bit tarnished from storage, and unused except the heater pins on one were once soldered... probably to check some tubes. $60 for the pair. Johnson 122-237 ceramic 7 pin giant socket for 813, etc. NOS, $15 Johnson 122-248 ceramic 7 pin septar socket (accepts 7094, 8877, 832A), with base ring & ceramic spring retained (parallel) plate bar for 832A. Used, good condition. $10 Johnson 124-115-2 UHF socket similar to Eimac SK-620. NOS, but, a mite tarnished from age. $40 Pair of ceramic 7 pin giant sockets for 813, etc. Used, $15 pair Amphenol MHV connectors: Two 28100 right angle cable males & two 27025 panel mount females. NOS -- $40 all. UG-932 A/U MHV Male Cable connectors, NOS -- $10 ea UG-961 A/U MHV Female Panel connector, NOS -- $12 Water cooled heatsinks -- 12" x 8" used, drilled for TO-3's plus a few diodes. Back is flat. 3/8" water lines. $50 pair ILG Electric Ventilation -- 17-18-022A squirrel cage type fan. Encased motor with 181-009-EA fan 115/230 VAC 1.6A/.8A 50/60Hz 3000 RPM 4+" round intake, 3+" x 4-3/4" rectangular output flange, weighs 25 lbs. used -- $25 Kooltronic -- Model DF1F016N Dual fan style 230 VAC -- 1.2A -- 60Hz -- 3000 RPM -- 3+" round intakes, 2.5" x 5" rectangular output flanges, 16" long by about 7" diameter overall, weigh 15 lbs. These look like NOS but, they are a mite dusty from storage. 3 available -- $20 ea. and of course some panel meters, see: http://wc6w.50webs.com/wc6wfsw/index.html?fr32.html Other parts also listed on my webpage: http://wc6w.50webs.com/wc6wfsw/ 73 & Good morning, Marv WC6W http://wc6w.50webs.com/ *

WTB AMERITRON QSK 5

I WOULD LIKE TO BUY AN AMERITRON QSK5 110VOLT IS PREFERABLE... IN PERFECT WORKING CONDX