Hi Tom!

30km from me was an amateur station.He heard me S5 on 145.200Mhz and S1 on 145.230 and 145.260Mhz.
I Tx with 0.5Watt.

Thanks

Hi all!

I realised that if I TX with my HT transceiver like on 145.200Mhz,it can be hear on 145.232Mhz and on 145.264Mhz and on 145.296Mhz....Every 32 khz plus and minus direction also.
If somebody hear me on S5 value on 145.200Mhz and around S1 on 145.232Mhz and on 145.264Mhz...

Any advice?

I like to get Sender 145 service manual .

Thanks
Zoli

Hi all!

I realised that if I TX with my HT transceiver like on 145.200Mhz,it can be hear on 145.232Mhz and on 145.264Mhz and on 145.296Mhz....Every 32 khz plus and minus direction also.
If somebody hear me on S5 value on 145.200Mhz and around S1 on 145.232Mhz and on 145.264Mhz...

Any advice?

I like to get Sender 145 service manual .

Thanks
Zoli

Hi!

I like to know where is R259 5.6kohm resistor on PLL board.
This resistor is normally between bazis and emitter on Q213.
Normally between ground and collector is 0V in Rx,but in my radio around 9-10V.
I measured with multimeter but no resistor.

Who can controll it?


Thanks
           Zoli

Hi!

I like to know where is R259 5.6kohm resistor on PLL board.
This resistor is normally between bazis and emitter on Q213.
Normally between ground and collector is 0V in Rx,but in my radio around 9-10V.
I measured with multimeter but no resistor.

Who can controll it?


Thanks
           Zoli

Hi!


 Yes, EUR version but instead of PBT using IF-Shift.I think it is a same.
 Data Level is different.

Thanks
            Zoli

Hi all!

I like to ask you:
 
1.It is possible to know that my IC-275H radio is europe or sweden version or other?
 
I have original package box on it:IC-275H  EUR #12
 
2.I thought my radio in europe version, but #12 code on package is sweden code like in service manual on page 1, but only A/E model ?Service manual is not clear to me.
H model has not #12 code in manual.
 
3.What is different between europe and sweden radio version?
 
Thanks
             Zoli HG5AZR
 

Hi all!

I like to ask you:
 
1.It is possible to know that my IC-275H radio is europe or sweden version or other?
 
I have original package box on it:IC-275H  EUR #12
 
2.I thought my radio in europe version, but #12 code on package is sweden code like in service manual on page 1, but only A/E model ?Service manual is not clear to me.
H model has not #12 code in manual.
 
3.What is different between europe and sweden radio version?
 
Thanks
             Zoli HG5AZR
 

Hi all!

I like to ask you:
 
1.It is possible to know that my IC-275H radio is europe or sweden version or other?
 
I have original package box on it:IC-275H  EUR #12
 
2.I thought my radio in europe version, but #12 code on package is sweden code like in service manual on page 1, but only A/E model ?Service manual is not clear to me.
H model has not #12 code in manual.
 
3.What is different between europe and sweden radio version?
 
Thanks
             Zoli HG5AZR
 

Hi all!

For europe version:
If I hear on 145.675Mhz a stronger repeater in FM mode I hear it on around
146.665Mhz because 146.665Mhz is out of band(more than 146Mhz)and filter doesn
work but I cant hear it on 144.685Mhz because 144.685Mhz is inside of
band(144-146Mhz)and filter is works.My radio is europe version.Difference is
about 990Khz.
If I hear on 144.675Mhz a stronger station in FM mode I hear it on 143.685Mhz
because 143.685Mhz is out of band(less 144Mhz) and filter dosnt work but I cant
hear it on 145.665Mhz because 145.665Mhz is in band(144-146Mhz)My radio is
europe version.Difference also 990khz.

If you have usa version(144-148Mhz)filter is different.
please test it in case:
If you hear on 147.500Mhz a stronger repeater in FM mode you hear it on around
148.490Mhz because 148.490Mhz is out of band(more than 148Mhz)and filter doesn
work but you cant hear it on 146.510Mhz because 146.510Mhz is inside of
band(144-148Mhz)and filter is works.Difference is about 990Khz.
If you hear on 144.500Mhz a stronger station in FM mode you hear it on
143.510Mhz because 143.510Mhz is out of band(less than 144Mhz) and filter dosnt
work but you cant hear it on 145.490Mhz because 145.490Mhz is in
band(144-148Mhz).Difference also 990khz.

Please test it,what is your experience.

Zoli HG5AZR

Hi all!

For europe version:
If I hear on 145.675Mhz a stronger repeater in FM mode I hear it on around
146.665Mhz because 146.665Mhz is out of band(more than 146Mhz)and filter doesn
work but I cant hear it on 144.685Mhz because 144.685Mhz is inside of
band(144-146Mhz)and filter is works.My radio is europe version.Difference is
about 990Khz.
If I hear on 144.675Mhz a stronger station in FM mode I hear it on 143.685Mhz
because 143.685Mhz is out of band(less 144Mhz) and filter dosnt work but I cant
hear it on 145.665Mhz because 145.665Mhz is in band(144-146Mhz)My radio is
europe version.Difference also 990khz.

If you have usa version(144-148Mhz)filter is different.
please test it in case:
If you hear on 147.500Mhz a stronger repeater in FM mode you hear it on around
148.490Mhz because 148.490Mhz is out of band(more than 148Mhz)and filter doesn
work but you cant hear it on 146.510Mhz because 146.510Mhz is inside of
band(144-148Mhz)and filter is works.Difference is about 990Khz.
If you hear on 144.500Mhz a stronger station in FM mode you hear it on
143.510Mhz because 143.510Mhz is out of band(less than 144Mhz) and filter dosnt
work but you cant hear it on 145.490Mhz because 145.490Mhz is in
band(144-148Mhz).Difference also 990khz.

Please test it,what is your experience.

Zoli HG5AZR

Hi all!

For europe version:
If I hear on 145.675Mhz a stronger repeater in FM mode I hear it on around
146.665Mhz because 146.665Mhz is out of band(more than 146Mhz)and filter doesn
work but I cant hear it on 144.685Mhz because 144.685Mhz is inside of
band(144-146Mhz)and filter is works.My radio is europe version.Difference is
about 990Khz.
If I hear on 144.675Mhz a stronger station in FM mode I hear it on 143.685Mhz
because 143.685Mhz is out of band(less 144Mhz) and filter dosnt work but I cant
hear it on 145.665Mhz because 145.665Mhz is in band(144-146Mhz)My radio is
europe version.Difference also 990khz.

If you have usa version(144-148Mhz)filter is different.
please test it in case:
If you hear on 147.500Mhz a stronger repeater in FM mode you hear it on around
148.490Mhz because 148.490Mhz is out of band(more than 148Mhz)and filter doesn
work but you cant hear it on 146.510Mhz because 146.510Mhz is inside of
band(144-148Mhz)and filter is works.Difference is about 990Khz.
If you hear on 144.500Mhz a stronger station in FM mode you hear it on
143.510Mhz because 143.510Mhz is out of band(less than 144Mhz) and filter dosnt
work but you cant hear it on 145.490Mhz because 145.490Mhz is in
band(144-148Mhz).Difference also 990khz.

Please test it,what is your experience.

Zoli HG5AZR

Hi all!


My friend experienced at mic connector with special mode to go service menu,it was succesfull to enter to service menu but something changed at service menu,my friend dont remember.
After this setting radio not works propely,power changing in unpossible(only on display changing:low,middle,high) or doesnt recognise external mike.Maybe other funktion problem,told me only booth problem that realised..
Resetting : S.MW.MW and SET.LOCK  pushing with PWR not helped.
 
This radio is possible to repair or difficult or other way to set at factory original setting?
 
 
Thanks
                  Zoli  HG5AZR

Hi all!


My friend experienced at mic connector with special mode to go service menu,it was succesfull to enter to service menu but something changed at service menu,my friend dont remember.
After this setting radio not works propely,power changing in unpossible(only on display changing:low,middle,high) or doesnt recognise external mike.Maybe other funktion problem,told me only booth problem that realised..
Resetting : S.MW.MW and SET.LOCK  pushing with PWR not helped.
 
This radio is possible to repair or difficult or other way to set at factory original setting?
 
 
Thanks
                  Zoli  HG5AZR

Hi all!

I tried to set at HPL 3.5V at 145.000Mhz in FM mode at R9 test point but it was
not possible.I used digital multimeter and oscilloscop also.
Maybe service manual has a failure?


Zoli