|
|
 Show Posts
|
|
Pages: [1]
|
|
1
|
eHam Forums / Elmers / FT 736 R CAT interfacing
|
on: December 20, 2012, 03:53:41 AM
|
|
Hi all
i recently bought an used FT 736 R
they claim it comes with CAT interfacing
Is it a thrue CAT interface like what ihave with CI-V interface on my IC910H?
any experience?
thanks
'73 de IZ2 HDN Max
|
|
|
|
|
2
|
eHam Forums / Computers And Software / FT 736 R CAT
|
on: December 20, 2012, 03:50:51 AM
|
|
Hi all
i recently bought an used FT 736 R
They claim CAT interfacing
Is is a thrue CAT managment like what i have with CI-V interface with mi ICOM IC 910 H?
Anybody else has experience?
merry Xmas!
Thanks
'73 de IZ2 HDN Max
|
|
|
|
|
4
|
eHam Forums / Satellites / doppler compensation with IC910 H
|
on: November 09, 2010, 03:15:02 AM
|
|
good morning everybody...
i am just jumping into satellite mode and,as it normally happens,i have confused idea.
1st question:how can i make use of the "satellite"function on my ic910H?I suppose this function works as a sort of Automatic Doppler Compensation...
2nd question:any hint in practical tunings procedures?
Thanks!
73 de IZ2 HDN Max
|
|
|
|
|
5
|
eHam Forums / Elmers / RE: send VCC thru coax
|
on: February 12, 2010, 05:08:27 AM
|
|
Many thanks Dennis.Good device.
I probably forgot to tell that i am injecting UHF RF into coax.The MFJ device has a cut off frequency of 60 MHZ and i am sending out 430 MHZ.
Best '73
IZ2 HDN Max
|
|
|
|
|
6
|
eHam Forums / Elmers / send VCC thru coax
|
on: February 12, 2010, 02:18:54 AM
|
|
i realize this could be a quite silly question..my IC910H sends Vcc thru coax to a remote preamplifier.Once on the mast,how can i get Vcc out from remote cable to feed into a UHF preamplifier which has a Vcc supply separated from RF?
Thanks!
'73 from IZ2 HDN Max
|
|
|
|
|
7
|
eHam Forums / Elmers / 6JS6C versus 6LB6
|
on: February 09, 2009, 07:32:12 AM
|
|
Many thanks Dick for quick reply.Unfortunately it seems that i have no other choice.
I am any any case looking for another supplier.
In case i am not lucky i have to go for the 6LB6.
As far as you know are any modifications needed if 6LB6 are installed?
best 73
Max
|
|
|
|
|
8
|
eHam Forums / Elmers / 6JS6C versus 6LB6
|
on: February 09, 2009, 07:22:41 AM
|
|
good morning all,
i recently bought an old FT101E.
I have to replace the two finals 6JS6C.
I only found 6LB6 instead.
Does anybody know if 6JS6C are fully compatible with 6LB6?
best '73 de IZ2 HDN Max
|
|
|
|
|
9
|
eHam Forums / Elmers / EH antennas
|
on: May 22, 2008, 06:58:38 AM
|
|
Thanks for the infos Dan.
I was also questioning about thinghs put aside the antenna(i.e. other support pipes,vertical antennas and so on)and how they can decrease the EH antenna efficency.
best '73 de IZ2 HDN Max
|
|
|
|
|
10
|
eHam Forums / Elmers / EH antennas
|
on: May 22, 2008, 05:49:04 AM
|
|
good morning!
Does anyone have experience in using an EH antenna?
It seems to be very ...site..sensitive!
thanks
best '73 de IZ2 HDN Max
|
|
|
|
|
13
|
eHam Forums / Satellites / rotor &software
|
on: July 20, 2007, 01:00:39 AM
|
|
i will just start to work the Ao satellites.Which rotor would anybody suggests me to buy,together with the appropriate control software for Windows XP?
'73 de IZ2 HDN Max
|
|
|
|
|
15
|
eHam Forums / Amplifiers / IC756 PROIII with AL-811H amplifier
|
on: January 30, 2007, 01:02:35 AM
|
|
i recently bought the faboulus Icom 756Pro III.I am also waiting for delivery of Ameritron AL811H.Has anybody experience in connecting the two units together?Any suggestion from experienced HAms in using the couple?
Thanks
IZ2 HDN Max
|
|
|
|
|
Loading...
|
