hi I am actually more interested in bringing the person to the fore ... someone knows something .. It was stolen from a club station

It is mine and was reported to Dusseldorf Police ... it does have a case number

It was not covered by insurance - it was personally owned

Also ... as pointed out .... if it is sold on ... its still stolen ... its not that persons... it remains my property!

ALso ... if you knowingly also find you have stolen gear you are legally obliged to report it .. if someone finds out that 'you' know then you could find
yourself an accessory .... in Europe its called handling stolen goods!

This radio is still in circulation I am sure .... someone will own  it ... wether that is still the person who sold it or someone else

The serials are recorded with Icom too ... if it ever passed their way too!

My question to you would be .. how you feel if your gear was stolen and passed on ... wouldnt you want someone to report it if they found out it was stolen

Just as bad as a stolen vehicle .. can get you in heaps of trouble!

If someone knows where this transceiver is .. please let me know ...

73 Simon ZL4PLM ex DL4PLM/GM4PLM

Stolen from DL0DX in Dusseldorf some years ago

I am still hunting the light fingered *()*)(* that stole them.

Please if you bought a sec hand IC756 pro3 , PS125 or SP-23 check the serial numbers

reward will be given if I ever track them down and find who stole them.

Icom IC756 Pro 3 serial 3301140 - 47097223114918

Icom PS125 Power Supply Serial 0301430 - 4909723113256

Icom SP-23 Ext Spkr - Serial 0000121 - 731797114563

73 Simon ZL4PLM ex DL4PLM/GM4PLM

hi all

I urgently need a manual for an RF Concepts 4-310 100w 70cm pa

can anyone scan and email a copy - please inc the cct diagram !

thanks

Simon GM4PLM/DL4PLM

gm4plm a.t hotmail dot com

the dial on the 251/451 and 551 as far as i remember are driven optically

my old 251 was fixed by cleaning the optical encoders on the dial!

there wasnt any dial slippage - if that fails you will need to poke around with a scope and see if the leds are working and also one fault i remember was with the digital decoding ie the chip goes fault and the debounce of the optical signal gets messed up

good luck!
 

hi

can someone scan and email me a copy of the manual inc cct diagram for this 100w 70cms amp?

thanks

Simon GM4PLM at hotmail.com

trying to repair a duff FT736 that was zapped by a busted amp on a field day!

looking for dead/dying or wounded FT736's for spares!

particular need a processor card (behind the front panel!)

help!

regards

Simon GM4PLM (simon<at>creoch.freeserve.co.uk)

Help!

trashed my VX10 programming software disk

can someone help with a replacement??

regards

Simon GM4PLM (simon<at>creoch.freeserve.co.uk)

Help!

I trashed my programming software for my VX10!

can anyone help me with a replacement?

regards

Simon GM4PLM (simon<at>creoch.freeserve.co.uk)

trying to repair a duff FT736 that was zapped by a busted amp on a field day!

looking for dead/dying or wounded FT736's for spares!

particular need a processor card (behind the front panel!)

help!

regards

Simon GM4PLM (simon<at>creoch.freeserve.co.uk)

Have a problem(?) on a newly aquired FT757GX2.

tuning across the band on cw signals in slow reveals jumps every 100Hz - I can hear the 10hz steps ok but then at 100hz there is a jump as it crosses th 100hz points leading to a jumpy received sound as you tune across the band.

having never owned a 757GX2 is this normal - I have checked the alignment voltages of the 2 PLL's and the seem fine

repaired the damaged LPF board and rig gives 100watts now so getting there after CB'r used it for 27FM!