|
|
 Show Posts
|
|
Pages: [1] 2 Next
|
|
1
|
eHam Forums / Amplifiers / One Amp 2 Rigs
|
on: September 06, 2012, 11:12:29 AM
|
|
I am currently using my Ameritron 811 with my IC-7600, using the relay cable to activate the amp. Can I use this same amp with my Kenwood rig. i.e. using a splitter in the rear of the amp and using two separate relay cables. Obviously not at the same time.
|
|
|
|
|
2
|
eHam Forums / Elmers / IC-7600 VOX
|
on: May 02, 2012, 01:41:07 PM
|
|
I'm having a heck of a time trying to come up with the right settings, to use vox with my Heil Pro Set headset. Any advise is welcome.
|
|
|
|
|
4
|
eHam Forums / Elmers / Dummy Load / Wattmeter
|
on: December 03, 2011, 10:17:03 AM
|
|
I have a MFJ-267 dummy load / wattmeter, when it is in the dummy load position and power is sent the reflected power needle move to the far left limit. This seems to me to be wrong there should be no movement? but then again I'm asking the Elmers. It is installed after the amp and tuner ( last in line before the antenna).
Thanks for any help.
|
|
|
|
|
5
|
eHam Forums / Elmers / Ameritron AL-811
|
on: October 13, 2011, 05:18:17 PM
|
|
Is it possible for the amp to produce power on 20M but not on 15M. This is what seems to be happening.
|
|
|
|
|
7
|
eHam Forums / Elmers / HRD & two radios
|
on: September 06, 2011, 02:54:15 AM
|
|
I have HRD logging my IC-7600 and want to log on my TS-590 also. I can't seem to find a menu to add a radio. It is possible to run 2 rigs, HRD is V5 latest install.
Thanks for any help,
W1KRK
|
|
|
|
|
8
|
eHam Forums / Computers And Software / HRD Multiple Radios
|
on: September 05, 2011, 12:32:59 PM
|
|
I have HRD running fine with my IC-7600 and want to link up my TS-590 also. Is this possible? as I can't seem to find a menu for adding a rig. HRD V5 the latest version.
Thanx
|
|
|
|
|
9
|
eHam Forums / Elmers / RE: SWR / Dummy Load
|
on: July 04, 2011, 04:31:11 AM
|
|
I am set up like this 7600> al811> at1kp > MFJ-267 > antenna, thanks for the input I will change it and it should work.
|
|
|
|
|
10
|
eHam Forums / Elmers / SWR / Dummy Load
|
on: July 04, 2011, 02:39:17 AM
|
|
When tuning G5RV into my MFJ-267 set at dummy load the SWR can be set properly. When I put the dummy load back into antenna mode the SWR is not even close to the original setting. IC-7600 into AL811 amp (OFF) to Palstar AT1KP tuner......Thanks
|
|
|
|
|
11
|
eHam Forums / Elmers / Coax for G5RV
|
on: June 13, 2011, 12:05:11 PM
|
|
Just put up my ( W8AMZ ) G5RV, I need some help on the correct coax. I will need 200' and some of it will be buried. Was looking at the Cable X Perts stuff and not so sure what one to use. Have used LMR 400 on my beam but it is not buried. Will probably be using the G5RV on 40 & 80 mostly....Thanks
|
|
|
|
|
12
|
eHam Forums / Elmers / RE: G5RV
|
on: June 04, 2011, 12:16:03 PM
|
|
It will be suspended in the middle on a tree and on both ends in a tree, it will be about 32-35 ft above ground
|
|
|
|
|
13
|
eHam Forums / Elmers / G5RV
|
on: June 04, 2011, 09:11:59 AM
|
|
I am putting up a G5RV in the trees, I can not get it installed at 180 degrees N to S, what is the maximum angle I can have and still be effective.....Thanks
|
|
|
|
|
15
|
eHam Forums / Elmers / HAM IV Rotator Calibration
|
on: March 20, 2011, 05:58:17 AM
|
|
Recently installed a new Ham IV, there is a switch on the rear panel of the control box and no mention in the set up of it's function. The manual instructions are not very clear on calibration. I can't seem to get my beam to point in the same direction as indicated. Do I have to actually have move the antenna on the mast to 180 deg ccw rotation before I can get this right? Thanks for any advise.
|
|
|
|
|
Loading...
|
