|
|
 Show Posts
|
|
Pages: [1] 2 Next
|
|
2
|
eHam Forums / MARS / RE: W3LK - MARS frequencies
|
on: July 06, 2011, 07:17:29 AM
|
|
I use to be a member of mars. I loved to go down to upper part of the 20 meter band and listen to the phone patch between military when the war was going on in Iraq Robert above 14.400 I think.
|
|
|
|
|
3
|
eHam Forums / Antennas and Towers and more / RE: Another radial question
|
on: April 20, 2010, 02:03:29 PM
|
|
I have an inverted l up at about 40 ft would radials help or a counterpoise. i do not have much room planning to run electric fence wire as radils or an counterpoise.I am planning to run about them 34 ft or so hope to get 4 or more I can run maybe 4 68 ft but need to run themm back to antennas but not connecting them.
|
|
|
|
|
4
|
eHam Forums / Antennas and Towers and more / RE: counterpoise or radials
|
on: April 08, 2010, 07:50:19 AM
|
|
I was hoping to figure what would be better for me. The radials need to be elevated and counterpoise needs to be in ground correct? It might be better to just run radials for my inverted l the inverted l is cut for 160 meters 123or so feet thanks Robert
|
|
|
|
|
5
|
eHam Forums / Antennas and Towers and more / counterpoise or radials
|
on: April 06, 2010, 08:45:46 AM
|
|
I am so confused radials or counterpoise or both? I was wondering which would be better radials or an counterpoise I have a chained link fence,I thought could be used for a countepoise and also run radials. I was wondering could you use electric fence wire as radials? thanks Robert
|
|
|
|
|
9
|
eHam Forums / Mods And Repairs / 100d yaesu
|
on: February 16, 2007, 07:53:54 AM
|
|
I have a 100d yaesu that does not receive on hf and 6 meters. i was wondering if anyone has a 100d that they would sell cheap that maybe i could use for a part radio. Thanks Robert
|
|
|
|
|
10
|
eHam Forums / Elmers / 520 kenwood
|
on: February 01, 2007, 11:53:26 AM
|
|
I want to switch my buxcomm rascal to the 520. I had the rascal for a yaseau radio can it be switch? thanks Robert 4 pin mic
|
|
|
|
|
11
|
eHam Forums / Elmers / Wiring a MC80 for TS830
|
on: February 01, 2007, 11:49:17 AM
|
|
does anyone have the wiring to a kenwood 520 4pin mic? i had this buxcomm wired to a yaseau 8 pin mic and hope i can wire the 520 to the buxcomm rascal. thanks Robert
|
|
|
|
|
12
|
eHam Forums / Elmers / 100D
|
on: February 01, 2007, 11:31:32 AM
|
|
I have 1 yaseau 100d that works great on vhf but does not receive on hf and 6 meters. The output on hf is ok also but but no receive any ideas on were to get it fixed and how much it will cost. thanks Robewrt
|
|
|
|
|
13
|
eHam Forums / Mods And Repairs / 520 kenwood
|
on: January 28, 2007, 08:54:31 AM
|
|
I have a kenwood 520 and a buxcom rascal interface the buxcom is wired for a yaseau 840 8 pin mic.I was wondering if the mic could be changed for the kenwood.I would apperiate any help i could get thanks Robert
|
|
|
|
|
15
|
eHam Forums / Mods And Repairs / yaseau 100D
|
on: January 25, 2007, 12:24:01 PM
|
|
I need a chip number TD 62783F ON board q5001 . I hope some one can tell were to find one and how much it costs. tks Robert
|
|
|
|
|
Loading...
|
