try grounding the tail pipe, I have used this for years and does wonders

I a, running both, the FREE on the XP computers and the $30.00 on the Windows 7 computers

I use Real VNC. I can sit down stairs and do every that can be done from the computer that is hooked to the Rig. I even have the same screens.

Its great for doing digital

my 2 cents
Lew
 

If you want a schematic for the Kantronic 3 Plus email me.
If you find the PTT transistor DO NOT USE A RADIO SHACK REPLACEMENT I did and they do not work, get the proper transistor

try grounding the tail pipe first. I have cut a low of problems this way

You should be reading 0Vac not 60Vac
At your service panel their should be a ground to netural bond.

You may want to get a Electriction on site to check out your wiring

I have had AT&T U-Verse for over 1.5 years with no problems. The RG and 7 computers and 2 D-Link 10,100,1000 switches sit in the shack.
I set-up the RG to run on a Cat-5 systemn to all the STB

Just my 2 cents
Lew

I tried your sujection with no luck, I am ordering a replace PCA for the remote head.
$90.00 is a lit better than $350.00 for the kit

Lew
N4HRA

I have a TS-B2000 in the model and my RC-2000 has died
This is the 2nd one that has the same problem over the last 5 years
replace the 1st one

On the RC-2000 if you press the power on bottom the display lights up you can hear the power relay in the TC-B2000 click, then the display goes out
I can press the power on button on the TS-B2000 and everything works

I have gone as far as connecting the RC-2000 to my other TS-2000 with the same results even used a different interconnect cable

Any idea?

Also I am looking for the RC-2000 service manual and schematic

Lew
N4HRA

Do you have your MENU Set-up
I am using the following:
50B AF  Input Level for Packet 5
50C Main BAnd AF output level for Packet 3
50D Subband AF Output Level for Packet 4
50E Main Sub Band Externam TNC = Main
Also make sure the program is using USB ACDIO CODEC

using the above I have no problems with the Signalink

Just my 2 cents
Lew

MICRS45 Radio Shack Replacement MicHTX-212 & HTX-242 w RJ45 Mic ...
Zen Cart! MICRS45 Radio Shack Replacement MicHTX-212 & HTX-242 w RJ45 Mic [MICRS45] - MICRS45Radio Shack Replacement Mic for HTX-212 & HTX-242 with RJ45
www.buxcomm.com/catalog/index.php?main_page

Microphones, Headsets, and EarphonesMICRS45 Radio Shack Replacement MicHTX-212 & HTX-242 w RJ45 Mic
MICRS45 Radio Shack Replacement MicHTX-212 & HTX-242 w RJ45 Mic. $24.98 - · MICSCREWS MIC SCREWS both types Mic Capture screws and Cable Clasp screws

www.buxcomm.com/catalog/index.php?main_page...18

In my set-up, I have 2 370wpc batteries, each battery postive is fused for 30 amps.
I have a diode in series with the Postive along with a 30amp fuse from the power supply the battery.
the float voltage for by batteries are 13.65vdc.

I adjusted the power supply for 13.65 + .7vdc

All my equipment is connected to the batteries

In my set-up, I have 2 370wpc batteries, each battery postive is fused for 30 amps.
I have a diode in series with the Postive along with a 30amp fuse from the power supply the battery.
the float voltage for by batteries are 13.65vdc.

I adjusted the power supply for 13.65 + .7vdc

All my equipment is connected to the batteries

I installed a G5RV jr. using a shack tunner I could only tune 20 & 40 meters.
I did a lot of research and found that you can still have a high SWR at the antenna but a 1:1 match at the radio when using a shack tuner feeding coax to a balaum to ladder line
I removed the balaum and installed a SGC ATU. It made a world of differance.
the ATU tunned the ladder line for the proper Z for a 1:1 SWR while maintain 50 ohns to the rig.

Just my 2 cents
Lew

The problem with the USB to RS232 converters is they do not goto logic 1 5Vdc most of them goto 3.5 - 4Vdc
we use RS232 with our UPS systems to et them up and after doing a lot of trial and error we found that Iconsepts 10260 does the best.

just my 2 cents

Lew
N4HRA