eHam.net - Amateur Radio (Ham Radio) Community

Call Search
     

New to Ham Radio?
My Profile

Community
Articles
Forums
News
Reviews
Friends Remembered
Strays
Survey Question

Operating
Contesting
DX Cluster Spots
Propagation

Resources
Calendar
Classifieds
Ham Exams
Ham Links
List Archives
News Articles
Product Reviews
QSL Managers

Site Info
eHam Help (FAQ)
Support the site
The eHam Team
Advertising Info
Vision Statement
About eHam.net


Reviews Categories | Antenna parts, accessories, incl. baluns, hardware, etc. | Balun Designs Model 55131e For End Fed Half Waves Help


Reviews Summary for Balun Designs Model 55131e For End Fed Half Waves
Balun Designs Model 55131e For End Fed Half Waves Reviews: 1 Average rating: 5.0/5 MSRP: $94.94
Description: For those that enjoy the LNR and Hy Endfed antennas, but
want to run more power, Balun Designs now offers an
excellent alternative. Built with the same craftsmanship as
all our other units, this new model will allow you to either
replace your current matching unit or construct a new mono
or multiband endfed half wave antenna. We have also
installed an additional stud which can be used for a
separate counterpoise rather than forcing the use of the
feedline's coax shield. The suffix "e" configuration also
includes the wire clip as shown but does not include wire.
Wire is shown for demonstration purposes only.

Most end fed half wave antennas have an impedance between
2500 and 3000 ohms so we have designed a unit to fall in the
middle of this range. Creating a very low SWR match is
accomplished by adjusting the overall length of your
antenna. The capacitor as shown in photos may change
depending on availability.

Caution: When used at full power rating of 1kW, the antenna
must have a low SWR on the band selected. That is, any SWR
measurement taken with the transformer at the feedpoint
should not exceed 1.5:1 with NO tuner in use. There are
numerous configurations available online that will
accomplish this on multiple bands (Google end fed half wave
antennas). If the transformer is used with an external
tuner in conjunction with a single wire antenna typically
130-135 feet in length, power should be reduced on those
bands that show an SWR above 1.6 to 2:5 without the tuner.
A level of 500-600 watts is the maximum with a further
reduction on any band measuring above 3:1.
Product is in production.
More info: http://www.balundesigns.com/model-55131-55-1-for-end-fed-half-waves-1kw/
Email Subscription
You are not subscribed to this review.

Subscribe!
My Subscriptions
Subscriptions Help

You can write your own review of the Balun Designs Model 55131e For End Fed Half Waves.

N4LQ Rating: 5/5 Aug 12, 2016 07:40 Send this review to a friend
Higher Power Alternative   Time owned: 0 to 3 months
I used this to replace the matching device on my "Myantennas EFW8010". The Myantennas torroid can't handle more than 150 watts cw for long. This one by Balun Designs has held up well to 500 watts thus far.
My antenna is 137' long and configured as an inverted L with the top at 55'. The transformer is near ground level. Grounding the box has little or no effect on SWR or performance however does improve lightning protection. I did notice some swr change on 30 meters when grounding and a bigger improvement with a 1/4 wave counterpoise, 25', but just on 30 meters. Probably due to the wire not being a half wave mult. on that band.
My only suggestion would be to reduce the strain on the top hook at much as possible by some means. The stress of the antenna and hot weather is causing the plastic to pooch out.
 


If you have any questions, problems, or suggestions about Reviews, please email your Reviews Manager.