eHam.net - Amateur Radio (Ham Radio) Community

Call Search
     

New to Ham Radio?
My Profile

Community
Articles
Forums
News
Reviews
Friends Remembered
Strays
Survey Question

Operating
Contesting
DX Cluster Spots
Propagation

Resources
Calendar
Classifieds
Ham Exams
Ham Links
List Archives
News Articles
Product Reviews
QSL Managers

Site Info
eHam Help (FAQ)
Support the site
The eHam Team
Advertising Info
Vision Statement
About eHam.net


Reviews Categories | Ham Work Bench Tools & Test Equipment | RF Calibrator for FPM-1 ( NOT A KIT ) Help


Reviews Summary for RF Calibrator for FPM-1 ( NOT A KIT )
RF Calibrator for FPM-1 ( NOT A KIT ) Reviews: 2 Average rating: 5.0/5 MSRP: $89.00
Description: The M3 Electronix, Inc. RF Calibrator is a convenient, single source, instrument that provides a fixed 10 MHz reference sine wave output with +0.00dBm, -10dBm, -20dBm, and -30dBm selectable outputs into a 50 lhm load. It is intended as an accessory to the M3 FPM-1 Frequency Counter/Power Meter Kit.

Four switches control all of the outputs from the calibrator. The toggle switches were selected for long life and are high quality, epoxy sealed, with less than 10 milliohm initial contact resistance.

- The ON/OFF switch controls power to the calibrator.
- The 10 MHz/20MHz selection switch provides two separate frequencies suitable for use as frequency standards. The source of these two frequencies is a 20 MHz TCXO with an accuracy of less than +/- 2 ppm from 10 degrees C to 60 degrees C. All calibration procedures for the M3 Universal Frequency/Power Meter (M3 FPM-1) are performed using the 10 MHz signal.
- The two level switches control the calibrator output from 0.0dBm to -30dBm. For 0.0dBm output, both switches must be in the DOWN position and for -30dBm output, both switches must be in the UP position. The output levels on the RF calibrator have been set to within 0.1dBm at the BNC connector. A calibration sticker is affixed to the back of each calibrator listing the actual output levels measured.

The M3 RF Calibrator requires a DC voltage between 8 and 15 volts @ 40mA applied to the 2.5mm power jack located on the side next to the ON/OFF switch. The center pin of the DC jack is positive. After powering the calibrator on, allow at least 15 minutes for the circuitry to stabilize before use.

The M3 RF Calibrator includes a DC power plug and male-male BNC adaptor.
Product is in production.
More info: http://www.m3electronix.com/
Email Subscription
You are not subscribed to this review.

Subscribe!
My Subscriptions
Subscriptions Help

You can write your own review of the RF Calibrator for FPM-1 ( NOT A KIT ).

VA7ION Rating: 5/5 Nov 10, 2009 15:28 Send this review to a friend
Outstanding products, outstanding after market support  Time owned: more than 12 months
This review was long overdue: bought every single piece of equipment this company has to offer. Never disappointed, outstanding products, outstanding after market support.

Thank you Mike and Mike#2
 
KC0DLP Rating: 5/5 Feb 19, 2006 17:06 Send this review to a friend
Excellent product  Time owned: 0 to 3 months
Bought this along with the 40dB tap attenuator, and the FPM-1 Freq/Power meter. This is an outstanding piece of test reference equipment. Given that test equipment like a frequency meter is only as good as the reference standard it is set against, I thought I should have a good one. This was designed to go along with the other two products, and the documentation for all 3 products are cross-referenced. The product is excellent, and I feel like I got more than my money's worth. The units these replaced are already "recycled" into my parts box. Technical support is outstanding from this company. Very quick, friendly, and courteous. I'm getting the Semiconductor Analyzer next, and all of these products will be fixed to my test bench for years to come.
 


If you have any questions, problems, or suggestions about Reviews, please email your Reviews Manager.