|
New to Ham Radio?
My Profile
Community
Articles
Forums
News
Reviews
Friends Remembered
Strays
Survey Question
Operating
Contesting
DX Cluster Spots
Propagation
Resources
Calendar
Classifieds
Ham Exams
Ham Links
List Archives
News Articles
Product Reviews
QSL Managers
Site Info
eHam Help (FAQ)
Support the site
The eHam Team
Advertising Info
Vision Statement
About eHam.net
|
| Reviews Summary for Almost All Digital Electronics Digital Frequency Displays |
|
Reviews: 7
|
Average rating: 5.0/5
|
MSRP: $49.95
|
|
Description: Various digital frequency displays for adding to homebrew rigs, commercial rigs without digital displays or build your own handheld frequency counter!
|
|
Product is in production.
|
|
More info: http://www.aade.com/dfd.htm
|
|
Email Subscription
You are not subscribed to this review.
Subscribe!
My Subscriptions
Subscriptions Help
|
You can
write your own review of the Almost All Digital Electronics Digital Frequency Displays.
|
KB1SIC
|
Rating: 5/5
|
Feb 26, 2011 05:43
|
Send this review to a friend
|
|
great investment
|
Time owned: 0 to 3 months
|
|
I ran the cables directly to the pins of the tubes.Ran the cables to the unit,powered up and had 21st technology in about 30 minutes.My Collins KWM-2 now tunes frequencies to +/- 10 hz.
|
|
SCUBA
|
Rating: 5/5
|
May 31, 2010 07:50
|
Send this review to a friend
|
|
On the Collins KWM-2
|
Time owned: 0 to 3 months
|
Unit works perfectly on the Collins KWM-2. If you use the tube covers, be sure to install the 3 jumpers inside the unit, otherwise it won't work.
I didn't care for running the RCA Jack cables from outside the KWM2 all the way to the tube cover circuit boards, so I installed two female RCA jacks on the back of the KWM2 and ran the cables to the rear of those jacks for the BFO and HFO functions.
There is still room for the K5GNA fan upgrade in the KWM-2, if you loosen the V-11 tube cover sheet metal screw and pivot the circuit board vertical instead of horizontal, the circuit board will fit between V16 and V15 allowing plenty of room for the fans.
I really wanted to do the direct wire to pins 9 of each tube in lieu of the tube covers, but didn't care for doing micro-surgery to the KWM-2.
There's no need to refer to the KWM-2 dial any more.
|
|
N9SKN
|
Rating: 5/5
|
Jan 15, 2010 19:47
|
Send this review to a friend
|
|
Stood behind the product
|
Time owned: 0 to 3 months
|
Regarding a general purpose programmable DFD2 kit for dual conversion receiver.
- I was notified by Neil promptly after ordering that the kit shipped.
- The kit was received promptly
- The kit was missing several resistors and caps. After notifying Neil, replacements were received just 2 days later.
- My DFD2 would indicate LSB when should have been USB and vice-versa. This was not a defect of the DFD2 - rather the architecture of the RX I installed it in.
Neil then sent me a re-programmed PIC so that the DFD2 displayed sidebands correctly in my RX at NO CHARGE, again received 2 days after notifying him.
AADE's DFD2 product now does what it should and AADE supported me until it did.
|
|
W2XC
|
Rating: 5/5
|
Mar 28, 2009 18:14
|
Send this review to a friend
|
|
Works Great!!
|
Time owned: 0 to 3 months
|
|
Just bought the DFD2-520 LCD readout for my TS-520S via the AADE web site. WOW - great communications & super fast shipping. The unit brings my TS520S into modern times. Reads out down to 10 Hz. (ie... 3.870.00Mhz) - DEAD accurate too (I checked against my lab equipment)! Automatically reads the ENTIRE frequency (yes even the Mhz.) AND automatically reads out the mode. OUTSTANDING PRODUCT!!
|
|
K8WV
|
Rating: 5/5
|
Sep 24, 2008 19:06
|
Send this review to a friend
|
|
On a Drake . . .
|
Time owned: more than 12 months
|
|
I've used one of these on a Drake R4B for a few years now, and am very satisfied. Good product.
|
|
N0CGF
|
Rating: 5/5
|
Sep 24, 2008 08:56
|
Send this review to a friend
|
|
Excellent
|
Time owned: more than 12 months
|
|
I have owned one for over 2 years and use it on my SB-102, and HW-101 Heathkits, and have installed them on other SB and HW series Heathkits. I cannot find any fault with them as if it was sold as a Heathkit for use with the series. I did use the SB-650 installation procedures with minor modification due to loading of the AADE to the HFO, BFO, and VFO. It is sure Great to have frequency readout to use with these rigs to use along with the analog dial. 73's N0CGF Dennis
|
|
SV8YM
|
Rating: 5/5
|
Sep 24, 2008 04:00
|
Send this review to a friend
|
|
Great value for money
|
Time owned: more than 12 months
|
|
Neil's (AADE) Digital Frequency Displays combine ease of use with excellent quality parts and workmanship. Very well designed, stable and reliable, they provide efficient frequency measurement solutions for very little money.
|
|
If you have any questions, problems, or suggestions about Reviews,
please email your Reviews Manager.
|
|
|
|
|
