Pages: [1]   Go Down

Author Topic: Electrical noise  (Read 285 times)

KC8EQF

  • Member
  • Posts: 34
Electrical noise
« on: March 31, 2023, 11:52:24 AM »

I have a ATS-20 receiver plagued by "frying bacon Sound" electrical interference. How is the best way to remove this noise?
Logged

K6SDW

  • Posts: 526
    • HomeURL
Re: Electrical noise
« Reply #1 on: March 31, 2023, 12:01:39 PM »

Try to find the source of noise...one culprit is power line electrical noise.

GL/73
Logged

K0RS

  • Member
  • Posts: 1501
Re: Electrical noise
« Reply #2 on: March 31, 2023, 12:10:28 PM »

There probably isn't a good solution to this other than find the source of the noise and eliminate it.  Most modern amateur transceivers have noise blanker circuits that are pretty effective on this type of interference...something the inexpensive ATS-20 lacks.  One could always add an external DSP to the audio output like a Timewave DSP-599 or DSP-59+, but the outboard processor would likely cost more than the radio and it still wouldn't be at the IF stage.  Try some detective work to try to track the noise source down.  Power companies can sometimes be helpful if you can convince them the noise is their responsibility.  Unfortunately RF noise is becoming more and more ubiquitous so you may have a challenging task.
Logged
"90% of the people in a pile-up have no idea what's going on.  It's up to you to be in the remaining 10%."  *W9KNI*

WA3SKN

  • Member
  • Posts: 8124
Re: Electrical noise
« Reply #3 on: March 31, 2023, 02:57:57 PM »

If you remove the antenna and put a short on the jack, do you still have the noise?  Then the noise is external to the radio.  Do you still have the noise when NOT in FM mode?  Is this in all modes?  All frequencies?
Finding the source may be difficult, since the info claims the external antenna is for FM use only.

-Mike.
Logged

NA6O

  • Posts: 41
    • HomeURL
Re: Electrical noise
« Reply #4 on: March 31, 2023, 05:14:22 PM »

Welcome to our modern world, saturated with RFI sometimes to the point of incapacitation. Post specific questions in the RFI forum. But start by reading the resources at  http://www.arrl.org/radio-frequency-interference-rfi  Basically, you have to work through a process that locates andidentifies sources of RFI and then attempt to mitigate those. It can be a long journey…

Gary NA6O
Logged

KC8EQF

  • Member
  • Posts: 34
Re: Electrical noise
« Reply #5 on: Today at 04:30:14 PM »

I have a ATS-20 receiver plagued by "frying bacon Sound" electrical interference. How is the best way to remove this noise?
I fixed the problem with a good ground and ferrite snap ons but, the problem remains on the low bands.
Logged

W1VT

  • Member
  • Posts: 6067
Re: Electrical noise
« Reply #6 on: Today at 04:37:52 PM »

The impedance varies as the square of the number of turns.
10 to 15 turns on an FT-240-31 or FT-240-43 ferrite core may be needed.  31 is better but 43 is less expensive.

It the wires are thin I'll use one core for multiple wires.  Such as the mouse and keyboard cable through one FT-240-31.
Logged

W9IQ

  • Member
  • Posts: 8862
Re: Electrical noise
« Reply #7 on: Today at 04:44:52 PM »

The impedance varies as the square of the number of turns.

This is only true for a low number of turns and then it only applies to the inductive reactance, not the impedance magnitude. The core has a complex permeability that exhibits resistance as a function of inductive reactance. As a result, impedance magnitude is not a direct correlation to the number of turns.

- Glenn W9IQ

Logged
- Glenn W9IQ

God runs electromagnetics on Monday, Wednesday and Friday by the wave theory and the devil runs it on Tuesday, Thursday and Saturday by the Quantum theory.
Pages: [1]   Go Up